Differences

This shows you the differences between two versions of the page.

--- 599 [2010/11/25 18:17]
n5na
+++ 599 [2010/11/25 18:23]
n5na [General]
@@ Line 14: / Line 14: @@
 ==== General ====
-Microphone Connector: 8-Pin
+  ***Microphone Connector:** 8-Pin
-Headphone Jack: 1/4" Stereo, accepts mono or stereo plug.
+  ***Headphone Jack:** 1/4" Stereo, accepts mono or stereo plug.
-External CW Key Jack: 1/8 " Stereo
+  ***External CW Key Jack:** 1/8 " Stereo
-External Speaker Jack: 1/8" Mono
+  ***External Speaker Jack:** 1/8" Mono
-Aux DC Output Connector: RCA x2
+  ***Aux DC Output Connector:** RCA x 2
-Frequency Range TX: Ham Bands Only (160-6M)
+  ***Frequency Range TX:** Ham Bands Only (160-6M)
-ACC Din Connector: 8 PIN DIN Connector - Line In, Line Out, Aux PTT, Ext Key, Clock/Data/Enable, Ground
+  ***ACC Din Connector:** 8 PIN DIN Connector - Line In, Line Out, Aux PTT, Ext Key, Clock/Data/Enable, Ground
-DC Power Connector: Power Pole
+  ***DC Power Connector:** Power Pole
-Fuse: Automotive Blade Style Fuse, 25 Amp 32V
+  ***Fuse:** Automotive Blade Style Fuse, 25 Amp 32V
-Frequency Range RX: 500 kHz � 30 MHz and 50 � 54MHz. Specifications apply within Amateur Radio bands only.
+  ***Frequency Range RX:** 500 kHz - 30 MHz and 50 - 54MHz. Specifications apply within Amateur Radio bands only.
-Tuning Step Size: 1, 10, 100, 1000, 10000
+  ***Tuning Step Size:** 1, 10, 100, 1000, 10000
-Frequency Stability: Maximum +/- 0.5 PPM over operating temperature
+  ***Frequency Stability:** Maximum +/- 0.5 PPM over operating temperature
-Antenna Impedance: 50 ohms nominal.
+  ***Antenna Impedance:** 50 ohms nominal.
-Antenna Connectors: 1 x SO-239 transceive
+  ***Antenna Connectors:** 1 x SO-239 transceive
-Modes: USB, LSB, CW, AM (optional), FM (optional)
+  ***Modes:** USB, LSB, CW, AM (optional), FM (optional)
-Memories: 100
+  ***Memories:** 100
-Frequency Accuracy: +-5Hz @25C, 1 Hz tuning resolution
+  ***Frequency Accuracy:** +-5Hz @25C, 1 Hz tuning resolution
-Supply Voltage Range: 13.8V +/-15%
+  ***Supply Voltage Range:** 13.8V +/-15%
-Operating Temp. Range: 0-50 degrees Celsius
+  ***Operating Temp. Range:** 0-50 degrees Celsius
-Dimensions (H x W x D): 2.9" x 8.5" x 10.25" (excluding knobs and connectors)
+  ***Dimensions (H x W x D):** 2.9" x 8.5" x 10.25" (excluding knobs and connectors)
-Weight: 7.25 lbs with all options
+  ***Weight:** 7.25 lbs with all options
-Construction: Molded plastic front panel, aluminum chassis and texture painted steel covers
+  ***Construction:** Molded plastic front panel, aluminum chassis and texture painted steel covers
-PC Control Port: USB (using CCS USB to UART Driver)
+  ***PC Control Port:** USB (using CCS USB to UART Driver)
-Display: Custom FSTN monochrome LCD
+  ***Display:** Custom FSTN monochrome LCD
-Display Backlight: 256 colors X 16 intensity levels
+  ***Display Backlight:** 256 colors X 16 intensity levels
 ==== Receiver ====
-SSB Sensitivity: Better than 0.7uV, 2.4khz, 10dB SINAD, preamp off
+  ***SSB Sensitivity:** Better than 0.7uV, 2.4khz, 10dB SINAD, preamp off
-AM Sensitivity: Better than 4uV, 30% Mod, 6kHz BW, 10dB SINAD, preamp off
+  ***AM Sensitivity:** Better than 4uV, 30% Mod, 6kHz BW, 10dB SINAD, preamp off
-FM Sensitivity: Better than 2.2uV, 5kHz Dev, 16kHz BW, 10dB SINAD, preamp off
+  ***FM Sensitivity:** Better than 2.2uV, 5kHz Dev, 16kHz BW, 10dB SINAD, preamp off
-Selectivity IF1: 2.4khz standard, 9.0015 MHz, 2 options
+  ***Selectivity IF1:** 2.4khz standard, 9.0015 MHz, 2 options
-Selectivity IF2: 30 KHz Lowpass filter
+  ***Selectivity IF2:** 30 KHz Lowpass filter
-Selectivity, DSP IF: 127 built-in DSP filters from 100-15000 Hz BW
+  ***Selectivity, DSP IF:** 127 built-in DSP filters from 100-15000 Hz BW
-Third Order Intercept Point (IP3): Typical 20dBm @ 20kHz tone separation/2.4 kHz roofing filter, 17dBm @ 2kHz separation/600Hz roofing filter, S5 method, preamp off
+  ***Third Order Intercept Point (IP3):** Typical 20dBm @ 20kHz tone separation/2.4 kHz roofing filter, 17dBm @ 2kHz separation/600Hz roofing filter, S5 method, preamp off
-IMD3 Dynamic Range: Typical 97dB/20kHz, 95dB/2kHz, 500Hz BW, calculated 2/3(IP3-Noise Floor), preamp off
+  ***IMD3 Dynamic Range:** Typical 97dB/20kHz, 95dB/2kHz, 500Hz BW, calculated 2/3(IP3-Noise Floor), preamp off
-Blocking Dynamic Range: 138dB/20kHz, 127dB/2kHz, 500 Hz BW, RF gain @ 12 o'clock, preamp off
+  ***Blocking Dynamic Range:** 138dB/20kHz, 127dB/2kHz, 500 Hz BW, RF gain @ 12 o'clock, preamp off
-LO Phase Noise: Typical -132dBc/Hz @ 20kHz, -121dBc/Hz @ 2kHz
+  ***LO Phase Noise:** Typical -132dBc/Hz @ 20kHz, -121dBc/Hz @ 2kHz
-Noise Floor: Typical -132dBm/500Hz BW/preamp on, -126dBm preamp off
+  ***Noise Floor:** Typical -132dBm/500Hz BW/preamp on, -126dBm preamp off
-IF Frequencies: 1st:9.0015 MHz, 2nd:22.5 kHz, 3rd:0Hz (DSP)
+  ***IF Frequencies:** 1st:9.0015 MHz, 2nd:22.5 kHz, 3rd:0Hz (DSP)
-IF Rejection: Better than 70dB
+  ***IF Rejection:** Better than 70dB
-st IF Image Rejection: Better than 90dB/HF bands, 70dB/6M
+  ***1st IF Image Rejection:** Better than 90dB/HF bands, 70dB/6M
-nd IF Image Rejection: Better than 73dB
+  ***2nd IF Image Rejection:** Better than 73dB
-Other Spurious Response Rejection: Rejection:>80dB
+  ***Other Spurious Response Rejection:** Rejection:>80dB
-Other Spurious Response Rejection: Birdies: Typically less than -100dBm equivalent (no more than 5 birdies greater than -100dBm equivalent)
+  ***Other Spurious Response Rejection:** Birdies: Typically less than -100dBm equivalent (no more than 5 birdies greater than -100dBm equivalent)
-Pass Band Tuning: +/- 2.1kHz, 5Hz steps. Small dead zone for centering
+  ***Pass Band Tuning:** +/- 2.1kHz, 5Hz steps. Small dead zone for centering
-Attenuator: 10 db
+  ***Attenuator:** 10 db
-PreAmp: Nominal 12 db
+  ***PreAmp:** Nominal 12 db
-Audio Output: 2W into 4 ohms, <3% THD
+  ***Audio Output:** 2W into 4 ohms, <3% THD
-RIT range: +/- 8.2 kHz
+  ***RIT range:** +/- 8.2 kHz
-RIT Step size: 10Hz
+  ***RIT Step size:** 10Hz
-S-Meter Reference: S9 = 50 uV RMS
+  ***S-Meter Reference:** S9 = 50 uV RMS
-TX>RX Recovery Time: < 20 ms
+  ***TX>RX Recovery Time:** < 20 ms
-RX Headphone Output: Designed for 16-32 ohms impedance headphones. Usable at 8 ohms
+  ***RX Headphone Output:** Designed for 16-32 ohms impedance headphones. Usable at 8 ohms
-AUX Audio Output: 500 mv
+  ***AUX Audio Output:** 500 mv
-Auto Notch: IF DSP, multi-tone
+  ***Auto Notch:** IF DSP, multi-tone
-RX Noise Reduction: IF DSP, adjustable
+  ***RX Noise Reduction:** IF DSP, adjustable
-Noise Blanker: Optional daughter board, 2 levels of blanking
+  ***Noise Blanker:** Optional daughter board, 2 levels of blanking
-RX Current Drain: 1.25 Amps
+  ***RX Current Drain:** 1.25 Amps
-General Coverage Receive: degraded specs outside ham bands
+  ***General Coverage Receive:** degraded specs outside ham bands
 ==== Transmitter ====
-RF Power Output: Adjustable, 5-100 W, +/- 1 dB
+  ***RF Power Output:** Adjustable, 5-100 W, +/- 1 dB
-CW & SSB Duty Cycle: continuous service @ 100W
+  ***CW & SSB Duty Cycle:** continuous service @ 100W
-AM,FM,AFSK,PSK Duty Cycle: continuous service @100W, 50% duty cycle (Tx/Rx)
+  ***AM,FM,AFSK,PSK Duty Cycle:** continuous service @100W, 50% duty cycle (Tx/Rx)
-CW/SSB TX Bandwidth: 2.4kHz Filter
+  ***CW/SSB TX Bandwidth:** 2.4kHz Filter
-AM TX Bandwidth: 6k
+  ***AM TX Bandwidth:** 6k
-FM TX Bandwidth: 15kHz Optional Filter
+  ***FM TX Bandwidth:** 15kHz Optional Filter
-Microphone Input Impedance:>10 k-ohms at 1 kHz
+  ***Microphone Input Impedance:** >10 k-ohms at 1 kHz
-Microphone Sensitivity: 1 mV RMS for full power output, internal gain adjustment, 9v dc power for electret elements
+  ***Microphone Sensitivity:** 1 mV RMS for full power output, internal gain adjustment, 9v dc power for electret elements
-FM Deviation: +/- 5 kHz peak nominal
+  ***FM Deviation:** +/- 5 kHz peak nominal
-AUX Level Input: variable, 200mV nominal
+  ***AUX Level Input:** variable, 200mV nominal
-SSB Carrier Supression:> 70 dB
+  ***SSB Carrier Supression:** > 70 dB
-Unwanted Sideband Suppression:> 60 dB at 1 kHz
+  ***Unwanted Sideband Suppression:** > 60 dB at 1 kHz
-Harmonic & Spurious Outputs: <-50dBc @100 W <30MHz; -60dB>30MHz; -43 dB <5 W
+  ***Harmonic & Spurious Outputs:** <-50dBc @100 W <30MHz; -60dB>30MHz; -43 dB <5 W
-T/R Switching: PTT or VOX on SSB, AM, FM, QSK on CW
+  ***T/R Switching:** PTT or VOX on SSB, AM, FM, QSK on CW
-CW Keyer Type: Internal Curtis Mode B
+  ***CW Keyer Type:** Internal Curtis Mode B
-CW Rise and Fall Times: 5ms
+  ***CW Rise and Fall Times:** 5ms
-CW Offset: adjustable
+  ***CW Offset:** adjustable
-CW Keyer Speed: 5-60 WPM, adjustable weighting
+  ***CW Keyer Speed:** 5-60 WPM, adjustable weighting
-Current Drain: transmit 20 amps typ.
+  ***Current Drain:** transmit 20 amps typ.
-Third Order Intermod: Better than 25dB below peak
+  ***Third Order Intermod:** Better than 25dB below peak
-SSB Generation: DSP Generated
+  ***SSB Generation:** DSP Generated
-No. of DSP generated TX bandwidths: 3 built-in DSP filters - automatically selected - standard = 2.4Khz for SSB/CW; optional = 6Khz for AM, 12Khz for FM
+  ***No. of DSP generated TX bandwidths:** 3 built-in DSP filters - automatically selected - standard = 2.4Khz for SSB/CW; optional = 6Khz for AM, 12Khz for FM
 ==== Antenna Tuner ====
-Type: Reversible L-network
+  ***Type:** Reversible L-network
-Matching frequency range: 160 to 10 Meters, no Six Meters
+  ***Matching frequency range:** 160 to 10 Meters, no Six Meters
-Matching impedance range: 10:1 SWR typical
+  ***Matching impedance range:** 10:1 SWR typical
 ==== Options ====
-Filters: 2.4K standard, optional = 300, 600, 1.8k, 6k, 15k
+  ***Filters:** 2.4K standard, optional = 300, 600, 1.8k, 6k, 15k
-Noise Blanker: daughter board module
+  ***Noise Blanker:** daughter board module
-Auto Tuner: daughter board module
+  ***Auto Tuner:** daughter board module

Trace:

Differences

Navigation

Search

Toolbox

QR Code