Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
588firmware [2018/10/31 17:44] n5na |
588firmware [2018/10/31 21:08] n5na [Omni VII Firmware History & Download Archive] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Omni VII Firmware History & Download Archive ====== | ====== Omni VII Firmware History & Download Archive ====== | ||
| - | **Note: The firmware downloads below are only the .ruf files, which is the actual file you upload to the Omni VII. You must use the Update program which comes with the latest firmware download from the [[http://radio.tentec.com/downloads/transceivers/588|Ten-Tec]] website to install the .ruf file.** | + | **Note: The firmware downloads below are only the .ruf files, which is the actual file you upload to the Omni VII. You must use the Update program which comes with the latest firmware download from the Ten-Tec website to install the .ruf file.** |
| ==== Version 1.001 ==== | ==== Version 1.001 ==== | ||
| Line 271: | Line 271: | ||
| *Changes that affect both Remote Mode and Radio Modes: | *Changes that affect both Remote Mode and Radio Modes: | ||
| *Improve transmit audio performance in FM mode. | *Improve transmit audio performance in FM mode. | ||
| - | ***Changes that affect Remote Mode only:** | + | **Changes that affect Remote Mode only:** |
| *Increased Ethernet Handling priority in Remote Mode. | *Increased Ethernet Handling priority in Remote Mode. | ||
| *Modified the Remote Mode displayed FAIL counter to include | *Modified the Remote Mode displayed FAIL counter to include | ||
| Line 289: | Line 289: | ||
| ==== Version 1.028 ==== | ==== Version 1.028 ==== | ||
| + | **[[this>./firmware/588_setup_v1.028.exe_.zip|Download 1.028]]** | ||
| + | *Decouple the Remote Encoder from the Main Encoder LOCK feature | ||
| + | *Improve RIT/XIT usage on the Remote Encoder | ||
| + | *Improve AM transmit audio | ||
| + | *Increase deviation in FM transmit audio | ||
| + | |||
| + | ==== Version 1.029 ==== | ||
| + | **[[this>./firmware/588_setup_v1.029.exe_.zip|Download 1.029]]** | ||
| + | *Improve the lower range of the SPOT Level feature | ||
| + | *Resolved Bandwidth crash due to a serial CAT command in remote/Ethernet mode | ||
| + | *Reject invalid frequency commands rather than limit them on the CAT interface | ||
| + | |||
| + | ==== Version 1.033 ==== | ||
| + | **[[this>./firmware/588_setup_v1.033.exe_.zip|Download 1.033]]** | ||
| + | *Improved FSK Transmit Power Level for 100 watts | ||
| + | *Corrected headphone AF level with headphones connected at power up | ||
| + | |||
| + | ==== Version 1.035 ==== | ||
| + | **[[this>./firmware/588_setup_v1.035.exe_.zip|Download 1.035]]** | ||
| + | *Improved Auto Tuner Power Settling for reliability | ||
| + | *Increased DSP output level in Sideband for hardware reliability | ||
| + | |||
| + | ==== Version 1.036 ==== | ||
| + | **[[this>./firmware/588_setup_v1.036.exe_.zip|Download 1.036]]** | ||
| + | *Improved Ethernet Audio reliability | ||
| + | *Improved handling of broken Ethernet packets, net effect was to improve Ethernet packet handling for control and audio streaming. | ||
| + | *Removed support for uncompressed audio via the Ethernet. (note, when using third party programs, ensure you enable compression for RIP and TRIP, otherwise the radio will not start "RIPing" audio) | ||
| + | *Added a bit to the ?T query to identify that the version does NOT support uncompressed audio. Refer to the programmers reference guide for more details. | ||
| + | *Increased priority of Ethernet audio packet handling. Preserving DSP functioning within allotted time. (e.g. AN, NR, etc. all still worked at least as well as version 1.035.) | ||
| + | *Improved handling of QRN/impulse type noise so it wouldn't prematurely load up AGC. | ||
| + | *Added Bandwidth to the rig memory recall/restore. This was added so that customers could store settings for digital modes using sideband as the mode but wanting a narrower bw filter. **Caveat, when going from 1.035 to 1.036, when one does a recall, the BW will get recalled as 12kc, simply adjust the bw to the desired value, and then re-save the VFO to Memory. From then on the bandwidth for that specific memory will get recalled properly. This should be done for all memories the user has already stored.** | ||
| + | *Added Memory Recall (*Rnn, nn=0..99) to the CAT interface | ||
| + | *Added Memory Write (*Snn, nn=0..99) to the CAT interface | ||
| + | *Note, for the above two commands, there is not a single query, once a memory recall is performed, then each parameter can be queried via the CAT interface individually. | ||
| + | *Improved logic on programming the DDS to help prevent the radio from being off frequency. Basically made the timing of the code a bit more robust, should help those who have seen the rig transmit off frequency, a very very rare occurrence. | ||
| + | |||
| + | ==== Version 1.037 ==== | ||
| + | **[[this>./firmware/588_setup_v1.037.exe_.zip|Download 1.037]]** | ||
