Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
omni30mmod [2017/04/29 12:51] n1ooq |
omni30mmod [2017/04/29 14:10] n1ooq |
||
|---|---|---|---|
| Line 33: | Line 33: | ||
| ==Building the bandpass filter== | ==Building the bandpass filter== | ||
| + | |||
| + | Bandpass filter schematic: {{:schem_-_ind_coup_b.png?300}} | ||
| + | |||
| The bandpass filter contains three wound toroidal cores. There are numerous instructions on winding available on the web. | The bandpass filter contains three wound toroidal cores. There are numerous instructions on winding available on the web. | ||
| Line 41: | Line 44: | ||
| The T50-6 toroidal cores, with their windings: {{:img0014a.jpg?100}} | The T50-6 toroidal cores, with their windings: {{:img0014a.jpg?100}} | ||
| - | The cores are stacked on a piece of a zip-tie and hot-melt glued in place. A separation between the cores, about equal to their own width, is provided between them. | + | The cores are stacked on a piece of a zip-tie and hot-melt glued in place. A separation between the cores, about equal to their own width, is provided between them. The 15 uH inductor, with 59 turns, is stacked in the middle. |
| The cores, stacked and glued to a piece of a zip-tie: {{:img0016a.jpg?100}} | The cores, stacked and glued to a piece of a zip-tie: {{:img0016a.jpg?100}} | ||
| + | |||
| + | The 56 pF capacitors are paralleled to total 112 pF, and the filter is wired as shown in the schematic. One side of the outer inductors is chosen as ground, and the taps are installed at the required number of turns up from this grounded end. | ||
| + | |||
| ==Adding the bandpass filter to the board== | ==Adding the bandpass filter to the board== | ||
| - | ==Adding the lowpass filter to the board== | ||
| - | ===Testing=== | + | The stack is hot-melt glued to the bandpass filter board. It is attached vertically in approximately the same position as the Tentec transformer can for the original mod. There is a resistor which must be moved - see the Tentec instruction sheet. |
| - | Bandpass filter schematic: {{:schem_-_ind_coup_a.png?300}} | + | Bandpass board, bottom side, showing pads for 30m mod. At left, output. At the center, ground. At right, input: {{:img0025a_-_edit.jpg?100}} |
| - | Bandpass board, bottom side, showing pads for 30m mod: {{:img0025a_-_edit.jpg?100}} | ||
| Bandpass board, top side, showing finished 30m filter mod (between bandswitch and the shield can at the right): {{:img0032a.jpg?100}} {{:img0033a.jpg?100}} | Bandpass board, top side, showing finished 30m filter mod (between bandswitch and the shield can at the right): {{:img0032a.jpg?100}} {{:img0033a.jpg?100}} | ||
| + | |||
| + | ==Adding the lowpass filter to the board== | ||
| + | |||
| + | ===Testing=== | ||
| Lowpass board, bottom side, showing pads for 30m mod: {{:img0019a_-_edit.jpg?100}} | Lowpass board, bottom side, showing pads for 30m mod: {{:img0019a_-_edit.jpg?100}} | ||
| Lowpass board, top side, showing finished 30m filter mod: {{:img0034a_-_edit.jpg?100}} | Lowpass board, top side, showing finished 30m filter mod: {{:img0034a_-_edit.jpg?100}} | ||
