VHF IF-DSP MULTI-MODE TRANSCEIVER





Amateur Radio's First
VHF IF-DSP transceiver!

Real innovation in a multi mode VHF transceiver was long overdue. Introducing the Ten-Tec model 526 "6N2" VHF transceiver. Amateur radios' first IF-DSP multi mode VHF rig. For a long time, there have been no affordable choices for either 6 or 2 meters in a single band VHF multi mode transceiver. Active hams planted the idea with us - why not offer a single rig that has BOTH 6 and 2 meters, without sacrificing performance? Multi mode HF/VHF rigs have been around for years, at over a thousand dollars and with compromised performance on the VHF bands at best. The 6N2 provides serious multi mode VHF performance in a small, take-anywhere package at a significantly lower price than HF+VHF multi mode transceivers. Why buy another HF rig to get VHF coverage, when you already own one?

Ten-Tec's years of experience designing DSP radio equipment for amateur, commercial, and military applications comes together to deliver a VHF multi mode transceiver to meet performance demands of weaker signal VHF operators. Let's take a look:

- SSB, CW, and FM transceive operation on both 6 and 2 meters. Extended receive range from 136-174 MHz on 2 meters.

- 35 IF-DSP bandwidth filters are built-in. No extra filtering to buy! Instantly select the best one for band conditions with the twist of a knob.

- Can be used as your main 2 meter FM rig. 100 memories, repeater splits, CTCSS tone encode are all built-in. Memories will retain mode, tone and split information. You can even program (and scan!) memories for different modes. Memory lockout function allows skipping constantly busy channels while scanning.

- Two SO-239 antenna connectors, one per band, allow you to leave antennas for both 6 and 2 meters connected. Separate amp keying lines allow connection of separate linear amplifiers for each band.

- 20 watts output power, front panel knob adjustable. Front panel meter does double duty as S-meter on receive and power output meter on transmit.

- Separate low level drive connection from 144 MHz for UHF and microwave transverters.

- All-mode squelch useful for FM repeaters or for quiet monitoring of SSB calling frequencies. Never miss a band opening again!

- Portable operation is a snap. The 6N2 is small and light enough to be carried anywhere. Only 4 ½ pounds! Current drain is minimal - only 400 mA @ 13.8 VDC on receive.

Priced at only $695 plus shipping. Accessory items: model 937 11 amp power supply, $89. Model 705 desk microphone $89.95. The 526 is supplied with a standard hand microphone.

 

GENERAL SPECIFICATIONS

MODES: CW, FM, LSB, USB
FREQUENCY RANGE: 50-54 and 144-148 MHz transceive. 136-174 MHz receive.
DISPLAY: 7 segment LED's for main and secondary DUAL VFO's with SPLIT mode
OFFSET TUNING: +/- 10 kHz receive
FM REPEATER OFFSETS: standard for 6m and 2m. Programmable for odd splits.
CTCSS: built-in, encode only.
MEMORIES: 100
ANTENNA: 50 ohms unbalanced, separate SO-239 output connectors for 6m and 2m
POWER REQUIRED: 400 mA receive (no signal), 6A transmit @ 12-14 VDC
CONSTRUCTION: 4 epoxy glass PC boards, molded front panel, aluminum chassis, texture painted steel top and bottom.
DIMENSIONS: HWD 2.75" x 8.5" x 8.75" (7 x 21.6 x 22.2 cm)

TRANSMITTER

RF OUTPUT: 1-20 watts, ALC stabilized
MICROPHONE INPUT: 200 to 50k ohms, 4 pin, front panel connector accepts microphones with 5 mv (-67 dB) output. Polarized voltage provided at mic jack for electrets.
T/R SWITCHING: PTT on SSB and FM, QSK on CW.
METERING: forward power
SSB GENERATION: DSP generated

RECEIVER

SENSITIVITY: .20 uv typical for 10 dB S+N/N @ 2.4 kHz bandwidth, SSB mode.
SELECTIVITY: 35 filters built-in; 200-1000 Hz in 50 Hz steps, 1000-2800 Hz in 100 Hz steps.
S-METER: Calibrated to 50 uv at S-9
I-F FREQUENCIES: 1st I-F 45 MHz, 2nd I-F 450 kHz, 3rd I-F 14.5 kHz

all specifications subject to change without notice