Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
705 [2007/02/13 23:14] n5na created |
705 [2012/01/25 22:49] (current) n1eu |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== Microphone Model 705 ====== | ====== Microphone Model 705 ====== | ||
+ | {{705.jpg?150|}}{{705btm.jpg?150|}} | ||
+ | |||
===== Description ===== | ===== Description ===== | ||
The Ten-Tec Model 705 is an Electret desk microphone designed for use as a station microphone in commercial and amateur radio communications and in public address and paging installations. The microphone consists of a base section and flexible gooseneck mounted microphone. The Model 705 incorporates a momentary type Push-To-Talk (PTT) button (gray), a Push-On, Push-Off locking type button (black), electronic circuitry to switch the microphone on, a signal amplifier that adds 13 dB of gain to the output level, an attached output cable and a battery compartment for a 9 volt alkaline battery. The PTT circuitry allows switching transmitters and/or transceivers, that have a low voltage positive T/R lines, into transmit mode. A light emitting diode in the base signals the transmit mode. | The Ten-Tec Model 705 is an Electret desk microphone designed for use as a station microphone in commercial and amateur radio communications and in public address and paging installations. The microphone consists of a base section and flexible gooseneck mounted microphone. The Model 705 incorporates a momentary type Push-To-Talk (PTT) button (gray), a Push-On, Push-Off locking type button (black), electronic circuitry to switch the microphone on, a signal amplifier that adds 13 dB of gain to the output level, an attached output cable and a battery compartment for a 9 volt alkaline battery. The PTT circuitry allows switching transmitters and/or transceivers, that have a low voltage positive T/R lines, into transmit mode. A light emitting diode in the base signals the transmit mode. | ||
- | The Model 705 | + | The Model 705 comes in two versions. The standard unit includes a four pin standard locking type cable connector which is pin compatible with Ten-Tec Models [[560]], [[561]], [[562]], [[563]], [[564]] and [[585]]. With a minor resistor change in the Models [[560]] and [[561]], the standard unit may be powered from the transceiver without the need for a 9 volt battery. The Model 705-A comes with a stereo 1/4" phone plug. This unit is compatible with the Ten-Tec Models [[525]], [[540]], [[544]], [[515]], and other early models. A 9 volt battery is required for the Model 705-A. |
+ | |||
+ | ===== Difference Between the 705 and 706 ===== | ||
+ | The 705 and [[706]] are essentially the same. The 706 does not have the compartment in the bottom to hold a 9V battery to supply voltage for the electret mic and circuitry. The [[706]] only works with rigs that supply the necessary voltage through the mic connector whereas the 705 can operate from rig voltage or battery. Also the 705 has a switch on the bottom to tell the controls on the mike base if you operate VOX or PTT. The 705 has a bit more versatility for use with older transceivers not having voltage present at the mic connector for the electret mic. | ||
+ | |||
+ | ===== Corsair Modification ===== | ||
+ | The documentation that accompanied the 705 microphone included information on modifying a Corsair I or early Corsair II (s/n before 1970) to power the 705 microphone. The modification involves shunting an existing 10K ohm resistor on the IF/AF board with a 470 ohm 1/2w resistor. | ||
+ | |||
+ | ===== Mods & Tips ===== | ||
+ | *[[705gain|705 Gain Mod]] | ||
+ | *[[705lowout|705 Low Output]] | ||
+ | *[[705conn|Connector Wiring]] | ||
+ | *[[706-588wiring|Wiring Diagram]] for an 8 pin connector | ||
+ | |||
+ | ===== Specifications ===== | ||
+ | ***Type:** Electret Condenser Microphone. | ||
+ | ***Sensitivity:** -52 dBV (0 dBV = 1 V/uBar @ 1 kHz). | ||
+ | ***Output Impedance:** Works with any circuit of 100 ohms or more. | ||
+ | ***Maximum Sound Pressure Level:** 130 dB | ||
+ | ***Battery Type:** 9 volt Alkaline transistor battery. | ||
+ | ***Electronics:** C-Mos PTT switch, C-Mos signal amplifier, NPN T/R transistor. | ||
+ | ***Current Required:** Receive mode: Less than 2 microamperes. Transmit mode: 2 milliamperes typical, with 9 volt battery. | ||
+ | ***Semiconductors:** 2 IC's; 1 Transistor; 7 Diodes. | ||
+ | ***Weight:** 12 oz. including battery. |