Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
588firmware [2018/10/31 17:48] n5na [Version 1.028] |
588firmware [2018/10/31 18:00] n5na [Version 1.036] |
||
---|---|---|---|
Line 271: | Line 271: | ||
*Changes that affect both Remote Mode and Radio Modes: | *Changes that affect both Remote Mode and Radio Modes: | ||
*Improve transmit audio performance in FM mode. | *Improve transmit audio performance in FM mode. | ||
- | ***Changes that affect Remote Mode only:** | + | **Changes that affect Remote Mode only:** |
*Increased Ethernet Handling priority in Remote Mode. | *Increased Ethernet Handling priority in Remote Mode. | ||
*Modified the Remote Mode displayed FAIL counter to include | *Modified the Remote Mode displayed FAIL counter to include | ||
Line 289: | Line 289: | ||
==== Version 1.028 ==== | ==== Version 1.028 ==== | ||
- | **[[this>./firmware/588_setup_v1.028.exe.zip|Download 1.028]]** | + | **[[this>./firmware/588_setup_v1.028.exe_.zip|Download 1.028]]** |
*Decouple the Remote Encoder from the Main Encoder LOCK feature | *Decouple the Remote Encoder from the Main Encoder LOCK feature | ||
*Improve RIT/XIT usage on the Remote Encoder | *Improve RIT/XIT usage on the Remote Encoder | ||
Line 295: | Line 295: | ||
*Increase deviation in FM transmit audio | *Increase deviation in FM transmit audio | ||
+ | ==== Version 1.029 ==== | ||
+ | **[[this>./firmware/588_setup_v1.029.exe_.zip|Download 1.029]]** | ||
+ | *Improve the lower range of the SPOT Level feature | ||
+ | *Resolved Bandwidth crash due to a serial CAT command in remote/Ethernet mode | ||
+ | *Reject invalid frequency commands rather than limit them on the CAT interface | ||
+ | ==== Version 1.033 ==== | ||
+ | **[[this>./firmware/588_setup_v1.033.exe_.zip|Download 1.033]]** | ||
+ | *Improved FSK Transmit Power Level for 100 watts | ||
+ | *Corrected headphone AF level with headphones connected at power up | ||
+ | |||
+ | ==== Version 1.035 ==== | ||
+ | **[[this>./firmware/588_setup_v1.035.exe_.zip|Download 1.035]]** | ||
+ | *Improved Auto Tuner Power Settling for reliability | ||
+ | *Increased DSP output level in Sideband for hardware reliability | ||
+ | |||
+ | ==== Version 1.036 ==== | ||
+ | **[[this>./firmware/588_setup_v1.036.exe_.zip|Download 1.036]]** | ||
+ | *Improved Ethernet Audio reliability | ||
+ | *Improved handling of broken Ethernet packets, net effect was to improve Ethernet packet handling for control and audio streaming. | ||
+ | *Removed support for uncompressed audio via the Ethernet. (note, when using third party programs, ensure you enable compression for RIP and TRIP, otherwise the radio will not start "RIPing" audio) | ||
+ | *Added a bit to the ?T query to identify that the version does NOT support uncompressed audio. Refer to the programmers reference guide for more details. | ||
+ | *Increased priority of Ethernet audio packet handling. Preserving DSP functioning within allotted time. (e.g. AN, NR, etc. all still worked at least as well as version 1.035.) | ||
+ | *Improved handling of QRN/impulse type noise so it wouldn't prematurely load up AGC. | ||
+ | *Added Bandwidth to the rig memory recall/restore. This was added so that customers could store settings for digital modes using sideband as the mode but wanting a narrower bw filter. **Caveat, when going from 1.035 to 1.036, when one does a recall, the BW will get recalled as 12kc, simply adjust the bw to the desired value, and then re-save the VFO to Memory. From then on the bandwidth for that specific memory will get recalled properly. This should be done for all memories the user has already stored.** | ||
+ | *Added Memory Recall (*Rnn, nn=0..99) to the CAT interface | ||
+ | *Added Memory Write (*Snn, nn=0..99) to the CAT interface | ||
+ | *Note, for the above two commands, there is not a single query, once a memory recall is performed, then each parameter can be queried via the CAT interface individually. | ||
+ | *Improved logic on programming the DDS to help prevent the radio from being off frequency. Basically made the timing of the code a bit more robust, should help those who have seen the rig transmit off frequency, a very very rare occurrence. | ||
+ | |||
+ | ==== Version 1.037 ==== | ||
+ | **[[this>./firmware/588_setup_v1.037.exe_.zip|Download 1.037]]** |