Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
540 [2008/04/07 01:47] n5na |
540 [2010/12/14 19:38] n5na [Related Links] |
||
|---|---|---|---|
| Line 23: | Line 23: | ||
| ===== Related Links ===== | ===== Related Links ===== | ||
| - | *[[http://kb.tentec.com/index.php?article=42|Ten-Tec Knowledge Base Article]] | + | *[[http://www.tentec.com/index.php?id=234|Ten-Tec Knowledge Base Article]] |
| Line 31: | Line 31: | ||
| *[[tritonpwr|Triton Power Connector]] | *[[tritonpwr|Triton Power Connector]] | ||
| *{{triton_iv_service_note_sn-1-540.pdf|Triton VI Service Note SN-1-540}} - Using Accessories with the Triton IV | *{{triton_iv_service_note_sn-1-540.pdf|Triton VI Service Note SN-1-540}} - Using Accessories with the Triton IV | ||
| + | *[[http://p1k.arrl.org/pubs_archive/74970|Add A Crystal Filter To Your Ten-Tec 540!]] (QST Archive - Must be an ARRL member to access.) | ||
| ===== Sales Information ===== | ===== Sales Information ===== | ||
| Line 39: | Line 40: | ||
| ===== Specifications ===== | ===== Specifications ===== | ||
| + | ==== General ==== | ||
| + | ***Frequency Bands:** 3.5 - 4.0, 7.0 - 7.5, 14.0 - 14.5, 21.0 - 21.5, 28.0 - 28.5, 28.5 - 29.0, 29.0 - 29.5, 29.5 - 30.0 MHz. Ten meter crystals furnished for 28.0 - 29.0 MHz. | ||
| + | ***All circuits permeability tuned.** | ||
| + | ***Tuning Rate:** Tuning vernier 25 kHz per revolution, typical. | ||
| + | ***Direct frequency readout:** Slide rule, color coded dial indicates 100 kHz segment, dial skirt increment to 1 kHz. Accuracy +/- 1 kHz from nearest 25 kHz calibration point. | ||
| + | ***Calibrator:** 25 Khz pulsed calibrator | ||
| + | ***Automatic sideband selection, reversible** | ||
| + | ***VFO Frequency Stability:** Less than 15 Hz change per F<sup>o</sup>, averaged over a 40<sup>o</sup> change from 70<sup>o</sup> to 110<sup>o</sup>, after 30 minute warmup. Less than 10 Hz change from 105 to 125 VAC line voltage when using TEN-TEC power supply. | ||
| + | ***Power Required:** 12-14 VDC, 500 mA receive, 18 A maximum transmit. | ||
| + | ***Modular Contruction:** 10 plug-in assemblies and 7 fixed circuit boards. | ||
| + | ***Semiconductors:** 47 transistors, 33 diodes, 11 IC's | ||
| + | ***Power switch remotely controls power supply.** | ||
| + | ***Snap-up front feet.** | ||
| + | ***Contruction:** Rigid aluminum chassis, sub-panels, top and bottom. Cycolac plastic side panels. | ||
| + | ***Finish:** Etched aluminum panel, textured black top and sides | ||
| + | ***Dimensions:** HWD 4.5" x 13.625" x 13" | ||
| + | ***Weight:** 12 lbs. | ||
| ==== Receiver ==== | ==== Receiver ==== | ||
