Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
599 [2010/11/25 18:14]
n5na 		599 [2018/11/01 03:24] (current)
n5na [Eagle Model 599]
Line 2: Line 2:
 {{599.jpg?​200|}}{{599rear.jpg?​250|Eagle Rear}} {{599.jpg?​200|}}{{599rear.jpg?​250|Eagle Rear}}
  
-This is a current production model. ​ Please visit [[http://​www.tentec.com/​index.php?​id=360|Ten-Tec,​ Inc.]] for more information.+
  
 ===== Description ===== ===== Description =====
Line 14: Line 14:
 ==== General ==== ==== General ====
  
-Microphone Connector: 8-Pin +  ***Microphone Connector:** 8-Pin 
- +  ***Headphone Jack:** 1/4" Stereo, accepts mono or stereo plug. 
-Headphone Jack: 1/4" Stereo, accepts mono or stereo plug. +  ***External CW Key Jack:** 1/8 " Stereo 
- +  ***External Speaker Jack:** 1/8" Mono 
-External CW Key Jack: 1/8 " Stereo +  ***Aux DC Output Connector:** RCA x 2 
- +  ***Frequency Range TX:** Ham Bands Only (160-6M) 
-External Speaker Jack: 1/8" Mono +  ***ACC Din Connector:** 8 PIN DIN Connector - Line In, Line Out, Aux PTT, Ext Key, Clock/​Data/​Enable,​ Ground 
- +  ***DC Power Connector:** Power Pole 
-Aux DC Output Connector: RCA x2 +  ***Fuse:** Automotive Blade Style Fuse, 25 Amp 32V 
- +  ***Frequency Range RX:** 500 kHz - 30 MHz and 50 - 54MHz. Specifications apply within Amateur Radio bands only. 
-Frequency Range TX: Ham Bands Only (160-6M) +  ***Tuning Step Size:** 1, 10, 100, 1000, 10000 
- +  ***Frequency Stability:** Maximum +/- 0.5 PPM over operating temperature 
-ACC Din Connector: 8 PIN DIN Connector - Line In, Line Out, Aux PTT, Ext Key, Clock/​Data/​Enable,​ Ground +  ***Antenna Impedance:** 50 ohms nominal. 
- +  ***Antenna Connectors:** 1 x SO-239 transceive 
-DC Power Connector: Power Pole +  ***Modes:** USB, LSB, CW, AM (optional), FM (optional) 
- +  ***Memories:** 100 
-Fuse: Automotive Blade Style Fuse, 25 Amp 32V +  ***Frequency Accuracy:** +-5Hz @25C, 1 Hz tuning resolution 
- +  ***Supply Voltage Range:** 13.8V +/-15% 
-Frequency Range RX: 500 kHz � 30 MHz and 50 � 54MHz. Specifications apply within Amateur Radio bands only. +  ***Operating Temp. Range:** 0-50 degrees Celsius 
- +  ***Dimensions (H x W x D):** 2.9" x 8.5" x 10.25" (excluding knobs and connectors) 
-Tuning Step Size: 1, 10, 100, 1000, 10000 +  ***Weight:** 7.25 lbs with all options 
- +  ***Construction:​** Molded plastic front panel, aluminum chassis and texture painted steel covers 
-Frequency Stability: Maximum +/- 0.5 PPM over operating temperature +  ***PC Control Port:** USB (using CCS USB to UART Driver) 
- +  ***Display:** Custom FSTN monochrome LCD 
-Antenna Impedance: 50 ohms nominal. +  ***Display Backlight:** 256 colors X 16 intensity levels
- +
-Antenna Connectors: 1 x SO-239 transceive +
- +
-Modes: USB, LSB, CW, AM (optional), FM (optional) +
- +
-Memories: 100 +
- +
-Frequency Accuracy: +-5Hz @25C, 1 Hz tuning resolution +
- +
-Supply Voltage Range: 13.8V +/-15% +
- +
-Operating Temp. Range: 0-50 degrees Celsius +
- +
-Dimensions (HxWxD): 2.9" x 8.5" x 10.25" (excluding knobs and connectors) +
- +
-Weight: 7.25 lbs with all options +
- +
-Construction:​ Molded plastic front panel, aluminum chassis and texture painted steel covers +
- +
-PC Control Port: USB (using CCS USB to UART Driver) +
- +
-Display: Custom FSTN monochrome LCD +
- +
-Display Backlight: 256 colors X 16 intensity levels+
  
 ==== Receiver ==== ==== Receiver ====
  
-SSB Sensitivity:​ Better than 0.7uV, 2.4khz, 10dB SINAD, preamp off +  ***SSB Sensitivity:​** Better than 0.7uV, 2.4khz, 10dB SINAD, preamp off 
- +  ***AM Sensitivity:​** Better than 4uV, 30% Mod, 6kHz BW, 10dB SINAD, preamp off 
-AM Sensitivity:​ Better than 4uV, 30% Mod, 6kHz BW, 10dB SINAD, preamp off +  ***FM Sensitivity:​** Better than 2.2uV, 5kHz Dev, 16kHz BW, 10dB SINAD, preamp off 
- +  ***Selectivity IF1:** 2.4khz standard, 9.0015 MHz, 2 options 
-FM Sensitivity:​ Better than 2.2uV, 5kHz Dev, 16kHz BW, 10dB SINAD, preamp off +  ***Selectivity IF2:** 30 KHz Lowpass filter 
- +  ***Selectivity,​ DSP IF:** 127 built-in DSP filters from 100-15000 Hz BW 
-Selectivity IF1: 2.4khz standard, 9.0015 MHz, 2 options +  ***Third Order Intercept Point (IP3):** Typical 20dBm @ 20kHz tone separation/​2.4 kHz roofing filter, 17dBm @ 2kHz separation/​600Hz roofing filter, S5 method, preamp off 
- +  ***IMD3 Dynamic Range:** Typical 97dB/20kHz, 95dB/2kHz, 500Hz BW, calculated 2/​3(IP3-Noise Floor), preamp off 
-Selectivity IF2: 30 KHz Lowpass filter +  ***Blocking Dynamic Range:** 138dB/​20kHz,​ 127dB/2kHz, 500 Hz BW, RF gain @ 12 o'​clock,​ preamp off 
- +  ***LO Phase Noise:** Typical -132dBc/Hz @ 20kHz, -121dBc/Hz @ 2kHz 
-Selectivity,​ DSP IF: 127 built-in DSP filters from 100-15000 Hz BW +  ***Noise Floor:** Typical -132dBm/​500Hz BW/preamp on, -126dBm preamp off 
- +  ***IF Frequencies:​** 1st:9.0015 MHz, 2nd:22.5 kHz, 3rd:0Hz (DSP) 
-Third Order Intercept Point (IP3): Typical 20dBm @ 20kHz tone separation/​2.4 kHz roofing filter, 17dBm @ 2kHz separation/​600Hz roofing filter, S5 method, preamp off +  ***IF Rejection:** Better than 70dB 
- +  ***1st IF Image Rejection:** Better than 90dB/HF bands, 70dB/6M 
-IMD3 Dynamic Range: Typical 97dB/20kHz, 95dB/2kHz, 500Hz BW, calculated 2/​3(IP3-Noise Floor), preamp off +  ***2nd IF Image Rejection:** Better than 73dB 
- +  ***Other Spurious Response Rejection:** Rejection:>​80dB 
-Blocking Dynamic Range: 138dB/​20kHz,​ 127dB/2kHz, 500 Hz BW, RF gain @ 12 o'​clock,​ preamp off +  ***Other Spurious Response Rejection:** Birdies: Typically less than -100dBm equivalent (no more than 5 birdies greater than -100dBm equivalent) 
- +  ***Pass Band Tuning:** +/- 2.1kHz, 5Hz steps. Small dead zone for centering 
-LO Phase Noise: Typical -132dBc/Hz @ 20kHz, -121dBc/Hz @ 2kHz +  ***Attenuator:** 10 db 
- +  ​***Preamp:** Nominal 12 db 
-Noise Floor: Typical -132dBm/​500Hz BW/preamp on, -126dBm preamp off +  ***Audio Output:** 2W into 4 ohms, <3% THD 
- +  ***RIT range:** +/- 8.2 kHz 
-IF Frequencies:​ 1st:9.0015 MHz, 2nd:22.5 kHz, 3rd:0Hz (DSP) +  ***RIT Step size:** 10Hz 
- +  ***S-Meter Reference:** S9 = 50 uV RMS 
-IF Rejection: Better than 70dB +  ***TX>RX Recovery Time:** < 20 ms 
- +  ***RX Headphone Output:** Designed for 16-32 ohms impedance headphones. Usable at 8 ohms 
-1st IF Image Rejection: Better than 90dB/HF bands, 70dB/6M +  ***AUX Audio Output:** 500 mv 
- +  ***Auto Notch:** IF DSP, multi-tone 
-2nd IF Image Rejection: Better than 73dB +  ***RX Noise Reduction:** IF DSP, adjustable 
- +  ***Noise Blanker:** Optional daughter board, 2 levels of blanking 
-Other Spurious Response Rejection: Rejection:>​80dB +  ***RX Current Drain:** 1.25 Amps 
- +  ***General Coverage Receive:** degraded specs outside ham bands
-Other Spurious Response Rejection: Birdies: Typically less than -100dBm equivalent (no more than 5 birdies greater than -100dBm equivalent) +
- +
-Pass Band Tuning: +/- 2.1kHz, 5Hz steps. Small dead zone for centering +
- +
-Attenuator: 10 db +
- +
-PreAmp: Nominal 12 db +
- +
-Audio Output: 2W into 4 ohms, <3% THD +
- +
-RIT range: +/- 8.2 kHz +
- +
-RIT Step size: 10Hz +
- +
-S-Meter Reference: S9 = 50 uV RMS +
- +
-TX>RX Recovery Time: < 20 ms +
- +
-RX Headphone Output: Designed for 16-32 ohms impedance headphones. Usable at 8 ohms +
- +
-AUX Audio Output: 500 mv +
- +
-Auto Notch: IF DSP, multi-tone +
- +
-RX Noise Reduction: IF DSP, adjustable +
- +
-Noise Blanker: Optional daughter board, 2 levels of blanking +
- +
-RX Current Drain: 1.25 Amps +
- +
-General Coverage Receive: degraded specs outside ham bands+
  
 ==== Transmitter ==== ==== Transmitter ====
  
-RF Power Output: Adjustable, 5-100 W, +/- 1 dB +  ***RF Power Output:** Adjustable, 5-100 W, +/- 1 dB 
- +  ***CW & SSB Duty Cycle:** continuous service @ 100W 
-CW & SSB Duty Cycle: continuous service @ 100W +  ***AM,​FM,​AFSK,​PSK Duty Cycle:** continuous service @100W, 50% duty cycle (Tx/Rx) 
- +  ***CW/SSB TX Bandwidth:** 2.4kHz Filter 
-AM,​FM,​AFSK,​PSK Duty Cycle: continuous service @100W, 50% duty cycle (Tx/Rx) +  ***AM TX Bandwidth:** 6k 
- +  ***FM TX Bandwidth:** 15kHz Optional Filter 
-CW/SSB TX Bandwidth: +  ***Microphone Input Impedance:** >10 k-ohms at 1 kHz 
-2.4kHz Filter +  ***Microphone Sensitivity:​** 1 mV RMS for full power output, internal gain adjustment, 9v dc power for electret elements 
- +  ***FM Deviation:** +/- 5 kHz peak nominal 
-AM TX Bandwidth: 6k +  ***AUX Level Input:** variable, 200mV nominal 
- +  ***SSB Carrier Supression:** > 70 dB 
-FM TX Bandwidth: 15kHz Optional Filter +  ***Unwanted Sideband Suppression:​** > 60 dB at 1 kHz 
- +  ***Harmonic & Spurious Outputs:** <-50dBc @100 W <30MHz; -60dB>​30MHz;​ -43 dB <5 W 
-Microphone Input Impedance:>​10 k-ohms at 1 kHz +  ***T/R Switching:** PTT or VOX on SSB, AM, FM, QSK on CW 
- +  ***CW Keyer Type:** Internal Curtis Mode B 
-Microphone Sensitivity:​ 1 mV RMS for full power output, internal gain adjustment, 9v dc power for electret elements +  ***CW Rise and Fall Times:** 5ms 
- +  ***CW Offset:** adjustable 
-FM Deviation: +/- 5 kHz peak nominal +  ***CW Keyer Speed:** 5-60 WPM, adjustable weighting 
- +  ***Current Drain:** transmit 20 amps typ. 
-AUX Level Input: variable, 200mV nominal +  ***Third Order Intermod:** Better than 25dB below peak 
- +  ***SSB Generation:** DSP Generated 
-SSB Carrier Supression:>​ 70 dB +  ​***No. ​of DSP generated TX bandwidths:** 3 built-in DSP filters - automatically selected - standard = 2.4Khz for SSB/CW; optional = 6Khz for AM, 12Khz for FM
- +
-Unwanted Sideband Suppression:>​ 60 dB at 1 kHz +
- +
-Harmonic & Spurious Outputs: <-50dBc @100 W <30MHz; -60dB>​30MHz;​ -43 dB <5 W +
- +
-T/R Switching: PTT or VOX on SSB, AM, FM, QSK on CW +
- +
-CW Keyer Type: Internal Curtis Mode B +
- +
-CW Rise and Fall Times: 5ms +
- +
-CW Offset: adjustable +
- +
-CW Keyer Speed: 5-60 WPM, adjustable weighting +
- +
-Current Drain: transmit 20 amps typ. +
- +
-Third Order Intermod: Better than 25dB below peak +
- +
-SSB Generation: DSP Generated +
- +
-# of DSP generated TX bandwidths: 3 built-in DSP filters - automatically selected - standard = 2.4Khz for SSB/CW; optional = 6Khz for AM, 12Khz for FM+
  
 ==== Antenna Tuner ==== ==== Antenna Tuner ====
  
-Type: Reversible L-network +  ***Type:** Reversible L-network 
- +  ***Matching frequency range:** 160 to 10 Meters, no Six Meters 
-Matching frequency range: 160 to 10 Meters, no Six Meters +  ***Matching impedance range:** 10:1 SWR typical
- +
-Matching impedance range: 10:1 SWR typical +
- +
-==== Ooptions ==== +
- +
-Filters: 2.4K standard, optional = 300, 600, 1.8k, 6k, 15k+
  
-Noise Blanker: daughter board module+==== Options ====
  
-Auto Tuner: daughter board module+  ***Filters:​** 2.4K standard, optional = 300, 600, 1.8k, 6k, 15k 
 +  ***Noise Blanker:** daughter board module 
 +  ***Auto Tuner:** daughter board module

Trace:

QR Code
QR Code 599 (generated for current page)