This is an old revision of the document!


Argosy Model 525

Description

The Argosy 525 is a medium power solid state transceiver covering 80, 40, 30, 20, 15, and 10 meters.

Reviews

  • ARRL (Must be an ARRL member and logged in to view.)

Mods & Info

Accessories

  • 2.4 kHz 8-pole ssb filter Model 220
  • 1.8 kHz 8-pole ssb filter Model 218
  • 500 Hz cw filer Model 217
  • 250 Hz cw filter Model 219
  • Audio cw filter Model 224
  • Noise blanker Model 223
  • Internal calibrator Model 226
  • DC circuit breaker Model 1125
  • Power Supply Model 225
  • Mobile Mount Model 222
  • Linear switching kit Model 1126

Specifications

General

  • Frequency Coverage: 3.5 - 4.0, 7.0 - 7.5, 10.0 - 10.5, 14.0 - 14.5, 21.0 - 21.5, 28.0 - 28.5, 28.5 - 29.0, 29.0 - 29.5, 29.5 - 30.0 MHz. (VFO provides approximately 40 kHz overrun on each band edge.)
  • Operating Modes: Normal sideband, reverse sideband, cw.
  • VFO Stability: less than 20 Hz change per oF averaged over a 40o change from 70o to 110o after a 30 minute warmup. Less than 15 Hz change from 105 to 125 VAC line voltage when using a Ten-Tec power supply.
  • Tuning Rate: Vernier, 18 kHz per revolution, typical.
  • Dial Calibration: +/- 2 kHz when zeroed to the nearest 25 kHz marker.
  • Antenna Impedance: Low impedance unbalanced (coaxial), 50 - 75 ohms.
  • Power Requirements:12 - 14 Vdc regulated to 5% or better. 500 mA receive; 9 A maximum transmit. Pwer switch remotely controls power supply.
  • Semiconductors: 42 Transistors, 4 FETs, 10 IC's, 52 Diodes, 3 PIN Diodes, 2 LEDs.
  • Construction: Rigid steel chassis. Dark painted, molded front panel. Dark painted aluminum back, top and bottom. Stainless steel tilt-up bail.
  • Dimensions: HWD 4" x 9.5" x 12" (bail not extended).
  • Net Weight: 8 lbs.

Receiver

  • Sensitivity: 0.3 uV for 10 dB S+N/N, typical.
  • Selectivity: 4 pole crystal filter. 2.5 kHz bandwidth, 2.7:1 shape factor @ 6/50 dB.
  • Audio Output: 1 watt at 8 ohms with less than 2% distortion. Built-in speaker.
  • I-F Frequency: 9 MHz.
  • Notch Filter: Greater than 50 dB rejection notch, tunable from 200 Hz to 3.5 kHz.
  • S-Meter: Automatically switched on when receiving.
  • Spurious Responses: More than 50 dB down except 28.980 MHz (which can be eliminated by using low end of 29.0 - 29.5 MHz band segment).
  • I-F Rejection: 60 dB.
  • Offset Tuning: Receiver, +/- 3.0 kHz, typical, detent center off.
  • Crystal CW Filters: Optional plug-in accessories. Model 217 has 500 Hz bandwidth, Model 219 has 250 Hz bandwidth.
  • Crystal SSB Filter: Optional plug-in accessory. Model 218 has 1.8 kHz bandwidth.
  • 8 Pole Crystal I-F Filter: Optional plug-in accessory Model 220. 2.4 kHz bandwidth. used in palce of standard plug-in 4 pole ssb filter.
  • Noise Blanker: Optional plug-in accessory, Model 223. I-F type, 50 dB blanking range.
  • Audio CW Filter: Optional plug-in accessory, Model 224. Center frequency 750 Hz. Position ONE has 450 Hz bandwidth down 10 dB at 400 Hz and 1500 Hz. Position TWO has 150 Hz bandwidth, down 40 dB at 400 Hz and 1500 Hz.
  • Calibrator: Optional plug-in accessory, Model 226. 25 kHz crystal type, pulsed tone.

Transmitter

  • DC Power Input: 100 or 10 watts, switchable. 100% duty cycle for up to 20 minutes, all bands.
  • RF Power Output: 40 - 50 watts in HI power position, 4 - 5 watts in LO power position.
  • T/R Switching: PIN diode antenna switch, push-to-talk on ssb, full break-in (QSK) on cw.
  • CW Sidetone: Internally generated. Adjustable tone and volume independent of af control. Operates only in cw mode.
  • SSB Generation: 9 MHz 4 pole crystal ladder filter. Balanced modulator. Converts to 8 pole with optional Model 220 filter.
  • Microphone Input: High impdeance crystal, ceramic or dynamic.
  • Carrier Suppression: 40 dB minimum.
  • Sideband Suppression: 30 dB minimum at 1 kHz tone.
  • Spurious Output: Less than -45 dB.
  • Meter: Indicates forward or reverse peak power on transmit, front panel switch.
  • ALC Control: High power only. LED indicator.

QR Code
QR Code 525 (generated for current page)